Sizes & Layouts

False Drawer Front Guide: Tip-Out Trays, Kit Sizes and Fixes

Noor K.Noor K.
Bright daytime kitchen sink wall with white shaker cabinets: the false drawer front above the sink base tilted forward to show a shallow white tray holding a scrub brush, matching drawer fronts on either side

A false drawer front is a fixed panel that looks like a drawer but has no drawer box behind it, used where a sink bowl or cooktop fills the space a drawer would slide into. On a kitchen sink base it keeps the band of drawer fronts unbroken across the counter, and a hinged tip-out tray can turn it into a slim pocket for sponges and brushes.

For sizing the sink cabinet itself, see our sink base cabinet sizes and types guide.

Key takeaways

  • Sink, vanity sink and cooktop bases use a fixed panel up top. In Fabuwood's Allure and Illume spec books it is 6¾ inches tall.
  • Fabuwood's tilt-out kits come in 11, 14 and 24 inches at $162.50 in Galaxy; Fabuwood's catalog says installation is included when the kit is ordered as an accessory on the cabinet.
  • The tray needs room between the panel and the sink bowl. Measure that gap before you buy.
  • Prefer a tall opening or more storage? A full-height door or a U-shaped pull-out may suit you better; removable ADA sink bases remain only in Galaxy Frost, in limited quantities while supplies last.
Table of Contents

What Is a False Drawer Front?

A false front is a drawer face with nothing behind it: a panel in the same door style and finish as the real drawers, fixed to the cabinet instead of to a drawer box. Without it, the top of a sink cabinet would show a gap in the middle of a run of drawer heads.

It can't be a working drawer because of space. Under a sink, the bowl hangs into the top of the box, exactly where a drawer would travel; under a drop-in cooktop, the burner housing does the same.

It is also called a faux drawer front, a fake drawer, a dummy drawer or a sink front. Our glossary entry has the short definition, and the parts of a kitchen cabinet guide shows where the panel sits relative to the face frame, rails and stiles.

Which Cabinets Have Fake Drawer Fronts?

Sink bases are the main cabinet with a fake drawer front, followed by vanity sink bases, diagonal sink fronts and cooktop bases; each gives up its top drawer to something that drops in from above. Here is where you meet them in the lines we sell:

  • Kitchen sink bases. Every Fabuwood Allure sink base from 21 to 42 inches has one or two false fronts over its doors. US Cabinet Depot names its Palermo and Torino sink bases "with false drawer front", and its framed spec book shows sink bases with single or double drawer fronts.
  • Corner sinks. Fabuwood's DSB36 diagonal sink base and DSF36 diagonal sink front both take the 11-inch tilt-out kit in the panel over the door; the DSB36FD drops that panel for one full-height door.
  • Cooktop bases. US Cabinet Depot sells a "two drawer with one false front" range base, the RB3DB, with a fixed panel on top for the cooktop and two working drawers below.
  • Converted bases. Fabuwood offers a modification that removes the drawer box and slides from a standard base and fixes the drawer face to the frame as a false front.

Farmhouse sinks are the exception. An apron-front sink shows its own front in the opening, so a farm sink base has no false front at all; Fabuwood's FS30 to FS36 ship with a closed panel the installer cuts to the sink. Our types of base cabinets guide shows these boxes side by side.

How Big Is the False Front on a Sink Base?

On a Fabuwood Allure sink base, the false front is 6¾ inches tall, the same as the top drawer on the drawer bases beside it, so the line across the room stays level. Width and the number of panels change with the cabinet.

Infographic of four sink base fronts in elevation: a 21-inch base with one false front and one door, a 30-inch base with one false front and two doors, a 36-inch base with two false fronts and two doors, and a 42-inch base with two false fronts and a 3-inch center stile, each false front labeled 6 3/4 in tall
Galaxy sink base fronts: one panel up to 30 inches, two panels on the standard 33 and 36, and a center stile at 39 and 42.

The table lists every Galaxy sink base, its front layout and our price in the finishes that share one price list, such as Frost, Dove and Nickel (the two oak finishes cost more).

Width Galaxy SKU Front layout Galaxy price Tilt-out tray listed?
21" SB21 One false front, one door $386.75 Yes
24" SB24 One false front, two doors $403.00 Yes
27" SB27 One false front, two doors $442.00 Yes (11" kit named for SB27)
30" SB30 One false front, two doors $461.50 Yes
33" SB33 / SB33SDF Two false fronts, or one full-width (SDF) $468.00 SB33 yes; SDF not listed
36" SB36 / SB36SDF Two false fronts, or one full-width (SDF) $490.75 SB36 yes; SDF not listed
39" SB39 Two false fronts, 3" center stile $526.50 Yes
42" SB42 Two false fronts, 3" center stile $572.00 Yes

Fabuwood's catalog lists the tray for the two-panel SB33 and SB36 but not for the single-front SDF versions at the same price. Want trays at 33 or 36 inches? Pick the two-panel box.

Other makers land close by. KCD's spec book gives its Oslo SB30 a 29½-by-6.7-inch false front over a 27-by-5¼-inch opening, and J&K lists its sink-front panels at 6 or 7 inches tall depending on door style.

How Does a Tip-Out Tray Work?

A tip-out tray is a shallow tray screwed to the back of the false front, with hinges at the bottom edge so the panel tilts forward instead of staying fixed. Pull the top of the panel and the tray swings out with it, putting a brush in your hand without opening the doors.

Tip-out, tilt-out and flip-out all name the same part. Fabuwood sells it as the TILTOUT 11", 14" or 24" kit: a molded white high-impact polystyrene tray with a ring holder and a soap dish, per Fabuwood's catalog. All three sizes are $162.50 in Galaxy (the 14-inch Frost kit).

Fabuwood's install note matters most: the kit "includes installation when ordered as an accessory on a cabinet." So add it to the same order as the sink base; a kit bought later doesn't carry that note, so plan on your installer fitting it.

J&K makes the tray standard on all of its kitchen and vanity sink bases: one on the 27-inch sink base, two on the 30- to 42-inch boxes. Our kitchen cabinet organizers guide compares the tray with the other small add-ons around the sink.

Which Tip-Out Kit Fits Your Sink Base?

The right tip-out kit is matched to the width of each false front panel, so Fabuwood pairs each kit size with specific sink base codes. This table pulls the pairings from Fabuwood's listings and the other makers' spec books:

Close daytime view of a white shaker 36-inch sink base with both false fronts tilted open, each revealing a shallow white tray with a ring holder and a soap dish holding a brush and a sink stopper
In Fabuwood's Illume pairings, a two-panel 33- or 36-inch sink base takes two trays, one behind each false front.
Line Kit Sink bases it is listed for Price
Fabuwood Allure (framed) TILTOUT 11" SB27 and VSB27 (kit listing); DSB36 and DSF36 diagonal fronts (cabinet listings) $162.50 in Galaxy
Fabuwood Allure (framed) TILTOUT 14" or 24" Tilt-out listed on SB21 to SB42; Fabuwood does not print which size each width takes, so we confirm it on the quote $162.50 in Galaxy
Fabuwood Illume (frameless) TILTOUT 11" SB27, VSB27 (two trays) $162.50 in Catalina
Fabuwood Illume (frameless) TILTOUT 14" SB21, SB24, SB24SD, VSB24, VSB24SD; SB33, SB36, VSB33, VSB36 (two trays) $162.50 in Catalina
Fabuwood Illume (frameless) TILTOUT 24" SB30, VSB30 $162.50 in Catalina
J&K Built in Standard on every kitchen and vanity sink base Included
KCD, US Cabinet Depot None listed The spec books we checked list no tilt-out kit; an aftermarket kit is the route Aftermarket

In Illume's pairings, the 33- and 36-inch sink bases take two 14-inch trays, while the 30-inch base takes one 24-inch tray, so a wider box doesn't always mean a wider kit. For an Allure box other than SB27, we confirm the kit size with Fabuwood on the quote.

For other lines, or a kitchen you already own, aftermarket sets fill the gap. Rev-A-Shelf sells molded 11- and 14-inch sets with self-holding hinges, stainless steel trays, slim trays for large sinks and a 36-inch tray you cut to length, from about $23 to $83 on its site when we checked. You can browse Fabuwood's kits on our tilt-out tray page.

What Stops a Tilt-Out Drawer From Opening?

A tilt-out drawer is stopped most often by the sink bowl: the tray swings back as the panel closes, and if the bowl sits too close behind the panel, the front won't shut. Measure the opening's width and height and the gap from the back of the panel to the bowl, then check them against the kit's specs. The common blockers:

Side-section infographic of a sink base: the false front tipping forward on a bottom hinge with a shallow tray on its back, the sink bowl behind it, and the gap between the back of the panel and the bowl marked as the measurement to take
The one measurement that decides a tip-out tray: from the back of the false front to the front of the sink bowl.
  • A big or deep bowl. Large single bowls and workstation sinks can sit close to the front. Slim trays exist for this: retailer listings give Hardware Resources' slim 11-inch kit a 1-9/16-inch tray depth.
  • Undermount clips and rails. Sink clips, and any support rail an installer adds, can sit where the tray swings.
  • An apron-front sink. There is no false front to hinge.
  • A center stile. The 39- and 42-inch bases have a 3-inch stile in the middle, so each tray stays behind one panel.
  • Soap dispensers and filters. A soap pump bottle or filter tubing near the front can foul the tray.

Framed and frameless boxes both take trays: Fabuwood lists tilt-out kits for its framed Allure and frameless Illume lines alike. An aftermarket kit's hinges screw to the sides of the frame opening, so on a frameless box check the kit sheet first. Our framed vs frameless guide explains the two builds.

How Do You Install a Tip-Out Drawer Kit?

A tip-out drawer kit installs in six steps with a drill, a 3/32-inch bit and a Phillips screwdriver. The sequence below follows Hardware Resources' published instructions; your kit's own sheet wins where it differs.

  1. Trace the opening. Trace the frame opening onto the back of the panel in soft pencil and mark the top.
  2. Remove the panel. See how it is held, then take it off carefully.
  3. Place the tray. Center it in the outline, drill pilot holes and leave the screws slightly loose so the tray slides off for cleaning.
  4. Fix the hinges to the cabinet. Match each hinge to its side of the opening and drill pilot holes, with tape on the bit as a depth stop.
  5. Fix the hinges to the panel. Line the hinge plates up with the lower corners of the outline and screw them on, top screw first.
  6. Hang the tray. Erase the outline and hang the tray on its two loose screws. Then cycle the panel to check it clears the bowl and sits flush with the drawers.

Unsure about drilling a new cabinet? Have your installer fit it; we sell and ship cabinets but don't install them.

How Do You Fix a Loose or Crooked False Front?

A loose false front is usually a fastener problem, so find how the panel is held and tighten or replace that part. Panels are commonly held by turn buttons, clips, screws from behind or glue blocks. These are general steps, not a manufacturer procedure; your cabinet maker's instructions win:

  1. Look up from inside. With a flashlight, find the fasteners behind the panel.
  2. Tighten what's there. A turn button that spins freely needs a new screw in fresh wood.
  3. Square it up. If the panel is crooked, loosen the fasteners, tap it into line with your hand or a rubber mallet (the method Decor Cabinets gives for its fronts) and tighten again.
  4. Replace worn clips. Push-on clip sets exist for this: Decore's false front connector set has two clips for the opening, two for the panel and six #6 x ½-inch screws, and needs a 4½-inch-tall opening.
  5. Check for water. A panel that won't hold screws may sit on a swollen rail; find the drip first.

A damaged panel is best replaced: J&K prints replacement sink-front panels by width (DS27 to DS42). For a cabinet bought from us, send a photo and the cabinet code and we will ask the manufacturer for the part. For door-side problems, see our hinge adjustment guide.

Do Bathroom Vanities Have False Fronts?

Most bathroom vanity sink bases have a false front for the same reason kitchen ones do: the bowl fills the top of the box. Fabuwood's Galaxy vanity sink bases are 34½ inches tall and 21 deep, with two false fronts on the 33- and 36-inch widths. Fabuwood's 11-inch kit listing names VSB27, and Illume pairs kits with its VSB24 to VSB36; the Galaxy vanity sink base listings themselves name no tray, so we confirm fit on the quote.

Bright bathroom with a 36-inch white shaker vanity sink base: two false drawer fronts across the top under a white undermount sink and pale quartz top, two doors below
A 36-inch vanity sink base with two false fronts across the top, the same arrangement as a kitchen sink base at vanity depth.

Vanities offer more ways to drop the false front. Illume lists full-height-door vanity sink bases (VSB24FD to VSB36FD), US Cabinet Depot's Shaker White SW-VS36FH is $590.48 against $357.72 for its standard VS36, and Galaxy's VSD30DL sink-and-drawer combo is $757.25. Our small vanities with drawers guide covers notched drawers, and you can browse every vanity sink base we carry.

When Is a Full-Height Door or Pull-Out Better?

A full-height door or a pull-out beats a false front when you store something tall under the sink, want the space organized, or need the cabinet to come out for wheelchair access. Here are the options with live Galaxy prices:

Option What you get Example and price Trade-off
Sink base with false fronts Matching drawer line, open interior Galaxy SB36, $490.75 Top band is dead space
Sink base plus tilt-out kit A pocket for brushes behind each panel Galaxy SB36 + TILTOUT kit, $653.25 Needs bowl clearance; little air
Single-panel front (SDF) One clean panel across the width Galaxy SB36SDF, $490.75 No tilt-out listed for it
Full-height door, corner sink A taller opening for a bin or filter tank Galaxy DSB36FD, $617.50 (same as DSB36) Breaks the drawer line
U-shaped pull-out A drawer that wraps the drain, with a small waste bin Galaxy SB30 + UVTCPO-30 BLUM, $461.50 + $646.75 = $1,108.25 Most cost; fit the plumbing first
Removable ADA sink base Doors, floor and toe kick come out for knee space Galaxy Frost ADA-SB36-R, $637.00 Galaxy Frost only, limited quantities while supplies last; 32½" tall

If you only want a home for brushes, add the tray, about a third more than the box. If you want the cabinet itself organized, the U-shaped pull-out more than doubles the box price but turns the space below into a real drawer; Fabuwood lists it for the VSB30-34, VB30FD and SB30, with Blumotion full-extension runners, four dividers and an 8-quart waste container.

Fabuwood has discontinued ADA cabinets in every style except Galaxy Frost; our ADA kitchen cabinets guide explains when a removable base is required. For waste pull-outs beside the sink base, see our Fabuwood accessories guide.

Frequently Asked Questions

Can you turn the fake drawer under a sink into a real drawer?

No, the sink bowl occupies the space a drawer box would slide through. You can add a tip-out tray behind the panel, or a U-shaped pull-out lower in the cabinet for real drawer storage.

What comes in a tip-out drawer kit?

A tip-out drawer kit usually holds two trays, two pairs of hinges and the mounting screws. Rev-A-Shelf's molded 6572 set pairs an open tray with one carrying a ring holder and soap dish; retailers list Hardware Resources' 11-inch kit with four self-closing hinges. The trays get little air, so keep brushes and gloves there rather than a wet sponge.

Can I add a tip-out tray to my existing sink cabinet?

Yes, most existing sink cabinets take an aftermarket kit if the bowl leaves room behind the panel. Measure that gap and the opening width, then buy a kit made for your cabinet type.

How much does a tip-out tray cost?

Fabuwood's tilt-out kits are $162.50 in Galaxy at any of the three sizes, and Fabuwood's catalog says installation is included when the kit is ordered as an accessory on the cabinet. Aftermarket sets on Rev-A-Shelf's site ran about $23 to $83 when we checked, but you fit them yourself.

Why won't my tip-out tray close?

A tip-out tray that won't close is usually hitting the bowl, a sink clip or a support rail. If it closes but sits crooked, the hinges are at different heights, so reset one. For bowl conflicts, look at a slim tray.

How do you remove a false front from a sink cabinet?

Open the doors, find how the panel is held and release those fasteners from inside. Decor Cabinets says its false fronts come off by tapping them from the inside by hand or with a rubber mallet. Support the panel so it doesn't drop.

Do frameless cabinets have false fronts?

Yes, frameless sink bases have false fronts too. Fabuwood's Illume spec book shows a 6¾-inch one, and US Cabinet Depot's Palermo sink bases carry one as well; Illume pairs its tilt-out kits by width.

Should you put handles on fake drawers?

Yes, put pulls on a sink-base false front if the drawers beside it have them, or the hardware line shows a gap. On a tip-out front the pull doubles as the handle. Keep the screws short so they don't reach the tray; our cabinet hardware guide covers sizing.

How long does a sink base with a tilt-out tray take to arrive?

A Fabuwood Galaxy sink base with its tilt-out kit typically ships in about 2 weeks in stock finishes such as Frost, Dove and Nickel; the Designer Collection colors Macadamia Beige, Pitch Black and Pistachio Green typically take 6–8 weeks. US Cabinet Depot takes about 3 business days flat-packed or about 5 assembled. Once an order is submitted, cancellation before production is possible only if the manufacturer accepts, with a restocking fee of typically 30%.

Plan Your Sink Wall With a Designer

Send us the sink's spec sheet, the wall width, what you keep under the sink and whether you want tilt-out trays. Our free 3D design service replies within two business days and usually returns renderings and an itemized quote within 24–48 hours of getting your measurements. Browse the Galaxy Frost sink bases, or order a Fabuwood door sample for $35 (samples are final sale) before you choose a finish.

We design, quote and ship cabinets to the lower 48 states; we do not install them. Your own contractor handles installation, and in New Jersey it is available through our sister company, Captivating Construction Group. Questions? Contact us or call (609) 900-3358.

Sources: Fabuwood Allure and Illume specifications guides and Galaxy Frost catalog listings; J&K, KCD and US Cabinet Depot spec books; captivatingcabinets.com prices (Fabuwood after the 35% discount), checked November 12, 2026; Hardware Resources tip-out tray instructions; Rev-A-Shelf tip-out tray catalog; Decor Cabinets on false fronts.

Found this useful? Share it
Add as a preferred source on Google
Noor K.

Written by

Noor K.

Technology Manager at Captivating Cabinets

Noor manages and develops the Captivating Cabinets website, and writes practical guides on cabinet styles, finishes, pricing, and remodel planning.

Your Cart

Your cart is empty.

Browse cabinets →
Free · No obligation

See your new kitchen before you spend a dollar

Send rough measurements and a few photos. A designer replies within 2 business days, and you get photorealistic 3D renderings with an itemized quote in 24–48 hours.

Contractors get trade pricing. Have a quick question? Ask Cabinets AI →

Kitchen designed with the free 3D design service from Captivating Cabinets