Galaxy Linen Vanity Accessories

Each product shows its list price beside the displayed one; the figures here are what you pay. The page as a whole spans $42.90 to $1,556.75, which tells you these are not one category of thing.

One caution applies to the whole table. The short descriptions on several of these listings were written generically and do not always agree with the manufacturer's catalog — the feet are described as filler strips, the U-shaped unit as a tip-out tray. Where that happens, the title and the code are the reliable half of the listing, and each sub-type page says what to confirm in writing.

A cabinet side is built to be hidden. In a kitchen it usually is; in a bathroom a vanity ends in open floor beside a door or a tub, and that side is in view from the hallway. On a white cabinet an unfinished side reads as a slightly different white. On this beige it reads as a different material altogether, because the exposed side is not the paint — the box interior is a natural wood veneer — and because a hardware-store beige will not match a finish with earthy, greige undertones. The fix has to come from the factory, in the same finish, or it will show.

Two factory routes exist, and a quote should carry one or the other, not both. The vanity cabinet listings describe a finished-side option at $96 per side, chosen per cabinet as left, right or both; ask us to confirm it on the box you are ordering. The other route is this page's panel family: GL VPF and GL SPF are listed as flat panels, GL VPCF and GL SPCF as shaker-profile, GL VPTF and GL SPTF as tall, each in V24 through V60 plus a TP1821 size, and each priced by the cabinet width it belongs to.

That width-based pricing is the reason to read the side panel page before buying one. A panel that finishes an end should cost the same whether the cabinet is 24″ or 60″ wide, because every bath box shares one height and one depth. These do not, and the manufacturer's codes decode to platform-and-foot assemblies — Vera or shaker profile, taper or cove foot — that sit under a vanity rather than beside it. If a plinth-mounted vanity is the goal, that is the part; if a plain finished end is, ask us to quote it by description rather than by code.

Two under-sink pull-outs here, and they are not two sizes of one thing. GL UVTCPO-30 BLUM is built for a 30″ sink base and is notched so the trap passes through the middle while storage rides forward on either side; manufacturer listings describe a waste container and four adjustable dividers with it, though the store's short description calls it a tip-out tray, so confirm by code. GL VOPO-24 BLUM is built for a 24″ sink base, has a flat floor, and is fitted with six reversible acrylic bins per the manufacturer — it needs the plumbing high and to one side, or it will stop at the trap.

• Sink base is 30″: the U-shaped unit. Order it after the plumber has set the drain, since the notch has a fixed position and the trap does not.
• Sink base is 24″: the organizer pull-out, provided the trap sits high or offset. Check the clear height under the lowest pipe first.
• Sink base is 36″ or wider: neither fits. Plan a drawer base beside the bowl instead — the builds on the vanities page show how.
• Two bowls on two 30″ sink bases: two U-shaped units, one per bay, is the only way to get the floor back under both.

Both run on Blum Tandem plus Blumotion runners, full extension and soft close, the same hardware under every drawer in the line. The fit checks, including the measurements to take inside the cabinet, are on the U-shaped sink base page and the organizer pull-out page.

Two parts take the dryer off the counter, and one question separates them: will there be an outlet inside the cabinet? GL VASR-30, at $240.50, is a rack that mounts inside a door on a 30″ vanity base; distributor listings describe two stainless bins with non-skid lining, and it has no outlet. GL VGO12FD BLUM, at $1,556.75, is a 12″ full-door unit with stainless bins, shelves and, per the same listings, an in-unit receptacle — which is why it costs more than most of the cabinets it goes near.

If the walls are open, decide now: the powered unit needs an electrician to bring a GFCI-protected receptacle inside the cabinet body at rough-in, and a 12″ opening designed into the run. If the walls are closed and the vanity is in, the door rack is the only one of the two you can add on a Saturday — check that the door still swings fully with a rack on it, and let tools cool before they go in, because nothing in the published spec calls the bins heat-rated.

And if the vanity is not yet ordered, neither may be the answer. A 12″ or 15″ drawer base — GL VDB12-34 or GL VDB15-34 — swallows tools, cords and brushes in one pull and costs less than the powered unit. Both parts are covered on the appliance storage rack page and the garbage pull-out page; the second is named for its bins, which are grooming-sized rather than household-waste-sized, so read it before assuming it is the trash cabinet.

This beige has an advantage here that a bright white does not. A painted dresser in a warm neutral is a piece most people recognize as furniture, and a shaker vanity in this finish, up on feet with brass pulls, gets there with very little help. Two parts push it that way, and using both at once is where it tips into costume.

GL TBF and GL CBF are bun feet for a vanity cabinet — taper and cove — at $42.90, and their titles say "for platform", which means they fasten to a plinth that carries the cabinet, not to the cabinet floor. Distributor listings give them at 4″ high, and the footed platform assemblies in the side panel family are catalogued at 5″ overall, so a 34½″ box on feet finishes near 41″ with a top. That arithmetic has to be settled before the countertop is templated, and the bun feet page works through which pairing lands at a usable height.

GL VDO is a decorative onlay at $425.75 — ornament made separately and applied to a door or panel face. Its dimensions, its substrate and whether it arrives painted in this beige or raw are not published anywhere we can verify, so ask all three before ordering. On a shaker door in a small bath it competes with the recessed panel it sits in; in a large room, on a vanity already up on feet, it can earn its place. The decorative onlay page makes the case for and against.

Sequence matters more here than in a kitchen, because three trades touch a bathroom vanity in the same week.

1. Finished sides or panels go on the same order as the cabinets; they are ordered against the cabinet width, so a late change to the vanity changes them too.
2. Feet and platforms are decided before the countertop is templated — the fabricator measures whatever height the cabinet stands at that day.
3. Interior pull-outs are ordered after the plumber has roughed in, and checked for full travel before the top goes on.
4. The door rack and the onlay can wait until you have lived with the room; both fit to a finished vanity.

Each part has its own page with the fit checks, the codes to confirm and an honest view of whether it is worth the money in your bathroom. The boxes themselves live on the vanities page, and if you would rather have the whole room drawn with the parts counted, our design service is free.